Customer Support

1000 Series inc G21/22 (all variants) 7

• 1000: What depth can 1000 hyperbaric sensor work at?
• 1000: How do I replace the dials on my Analox 1000?
• 1000: What would happen if I apply too much gas pressure (over-pressure) to my 1000 sensor?
• 1000: What diameter (size of tubing should I use to connect to the Analox 1000 flow adaptor?
• G22: G22 doesn't reach 100% after calibration

View all 7

A50 16

• A50 (with O2): 4-20mA output
• A50: 4-20mA without display?
• A50: Accessory device control
• A50: Alcane gas sensitivity?
• A50: How often does the A50 need servicing?

View all 16

ACG+ 2

• FOR ALL ACG SOLUTIONS, PLEASE VISIT THE PORTABLE ANALYSER PAGE
• ACG+: Power ranges

Aspida (all variants) 1

• ASPIDA SOLUTIONS CAN BE FOUND IN PORTABLE PRODUCTS SECTION

Ax60+ 10

• Ax60+: How to silence and acknowledge latched alarms
• AX60+: How do I disable the Alarm sounders?
• How do I fix a loose RJ45 connector on my Ax60+?
• How do I connect multiple sensors to the Ax60+ central display unit (hardwired)?
• What should I do if my Ax60+ has a FLT16 on the display?

View all 10

CO Clear 1

• CO Clear: Relay Operation

Fixed Sub (all variants) 4

• Sub MKIIF: Display problem
• Sub MKII: How to calibrate the device?
• Sub Mk III F depth sensor calibration
• Sub MKIIIF: Cable Identification.

Hypergas MkII 2

• Hypergas MkII: Messages / indications
• Hypergas MkII: Electrical questions query

O2NE+ / Safe-Ox+ 19

• Can I have two relays trigger from one alarm?
• Can I use an older repeater with a newer O2NE+ or Safe-Ox+ unit?
• How do I adjust the alarm setpoints on my O2NE+ or Safe-Ox+ device?
• How do I retrofit relays to my O2NE+ or Safe-Ox+ device?
• My O2NE+/Safe-Ox+ readings change with vibration

View all 19

SDA (all variants) 6

• SDA: Difficulty installing SDA software on a Microsoft laptop
• SDA: How do I install the SDA PC tool in Windows 10?
• SDA O2: Calibration Adjustment
• SDA: Setup Tool Displays Incorrectly On My Laptop
• SDA: How do I reconfigure my Analox SDA device?

View all 6

COSAMS 0

Venus 1

• Venus Pro: Calibration Issue

SV-Range 2

• Sensor life
• Calculating Output

101D2 Portable Oxygen Monitor 1

• How do I conduct an air calibration of the 101D2?

ACG+ 18

• ACG: COSHH regulations?
• ACG: Heliox / Trimix mixes?
• ACG: Introductory video
• ACG: Nitrox gas mixes?
• ACG: Recommended oil mist sample frequency?

View all 18

Aspida (all variants) 10

• Aspida: (All) My device refuses to calibrate
• How do I connect an SDA flow meter panel to my ADM Aspida?
• Aspida (all variants): ASPIDA software download
• Sub Aspida: How do I calibrate using the Aspida Configuration Software?
• Sub Aspida: How do I change the Oxygen sensor?

View all 10

ATA Pro 4

• ATA: (Pro) Battery life?
• ATA: (Pro) Helium displays 133 or Err?
• ATA: (Pro) High temperature operation
• ATA: (Pro) Sensor change and calibration

CO2 Buddy 3

• Q: My CO2 Buddy is reading 9.99 and wont stop alarming.
• Q: My CO2 Buddy is displaying F60. What do I do?
• Q: CO2 buddy condensation issue

EIICO 1

• EIICO: How do I bump test it?

O2EII Pro 8

• O2EII: Crush test
• O2EII: Graded warranty?
• O2EII: Sensor life?
• O2EII: What does code 'L' or 't' mean?
• O2EII Pro: How do I replace the battery on the O2EII?

View all 8

Mini O2 Portable 1

• Mini O2 Portable: Pressure

Sub MkIIP 4

• Sub MKIIP: Familiarisation video
• Sub MKIIP: Sensor explanation
• Sub MKIIP: Servicing
• SubMkIIP: Convert mBar.pp O2 to %O2

3000SI Series (all variants) 2

• 3000SI: Using the 3000SI devices at lower pressures
• 3000SI: What is the accuracy of 3000SI cells?

Status Scientific: MCU and LC series panels 4

• How often does the MCU datalog?
• How do I connect my 3000SI sensor to a Status Scientific LC control panel?
• Why is the oxygen sensor (on my LC panel) reading low?
• LC Panel: FGD3 Infra-Red sensor connection